Just How To Install A Bath Tub (For Novices).
Just How To Install A Bath Tub (For Novices).
Blog Article
We have noticed this post pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround listed below on the internet and think it made good sense to write about it with you in this article.
Installing a bathtub isn't specifically brain surgery, however it does need solid plumbing, woodworking, and also often, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately hard task. If the old tub is readily accessible, the task can move quickly; if you have to open up a wall to remove the old bathtub as well as position the brand-new tub, the job is a lot harder. In either case, the task is within a house handyman's skills, although you will require a helper to vacate the old bathtub and embeded in the brand-new one. Ensure you have actually certified yourself for the work as well as are comfortable trying it. Rather than working with a specialist to take over a halfway-completed task, it is much better to consider using one before you begin. Chances are you might need a specialist plumber to make tube connections.
This write-up will aid you set up a new tub in your bathroom if you have actually already gotten a new bathtub and do not need to alter the arrangement of your previous water system pipes.
Your devices and product checklist must comprise the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, after that the first thing you ought to do is separate the supply of water. After doing so, switch on the faucets to drain pipes any water staying in the system. The procedure of getting rid of the existing taps can be rather bothersome as a result of the restricted gain access to that is often the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will certainly come from the pipelines. Once the supply pipes have been removed, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any old sealing compound.
Prior to going on to fit the brand-new taps, compare the pipeline links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap and the other end offers a link to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin ensuring that the washers are in location in between the faucet and also the sink. Secure the tap in place with the producer supplied backnut. As soon as the faucet is firmly in place, the supply pipes can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The previous kind needs to be attached to the tap ends first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Utilizing both wooden boards under its feet, place the bathtub in the required placement. The wood boards are practical in equally spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four small points.
The following objective is to make sure that the tub is leveled all round. This can be achieved by checking the level and also changing the feet on the bathtub until the level checks out level.
To install faucets, fit all-time low of the furthest flexible faucet adapter to the proper supply pipe by making a compression join; after that do the exact same for the other faucet.
Activate the water system and examine all joints and also new pipework for leaks and also tighten them if needed. Fill the bath tub as well as also check the overflow outlet and the regular electrical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the maker's instruction manual. Tiling and also sealing around the bathtub must wait up until the bath tub has actually been used at the very least once as this will certainly resolve it into its last position.
Planning for the Setup
Firstly, the sustaining frame provided with the bath needs to be fitted (if needed) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets system to stop stress on the bath tub.
Fit the flexible faucet connectors to the bottom of both faucets utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be suited its last position.
Tiling Around the Bath tub
In the location where the bath satisfies the tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to fracture a rigid seal, triggering the water to pass through the wall surface between the bathroom and also the tiling, resulting in issues with wetness and possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures and installations. They are marketed in tubes and also cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of drenched paper or soft rope. Remember to always fill the bathtub with water before sealing, to enable the motion experienced when the tub is in use. The sealant can break relatively very early if you do not take into consideration this motion prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly available on the market. It is recommended to fit the tiles using water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like reading about How to Install a Bathtub Yourself? Write a remark down the page. We will be interested to know your ideas about this blog posting. We hope that you come back again soon. Kindly take the time to promote this entry if you enjoyed reading it. Thanks for going through it.
Book A Service Report this page